Etc SmartFade v2.0.0 Two Scene Quick Guide Uživatelský manuál stáhnout pdf

Faders:

Use the faders to set levels for individual control channels. If SmartFade

is set to use a 1=1 patch, fader 1 controls dimmer 1, fader 2 controls

dimmer 2, and so on.

• SmartFade 1248 Faders 1-12 control dimmers 1-12 on Scene B, and

faders 13-24 control dimmers 1-12 on Scene A.

• SmartFade 2496 Faders 1-24 control dimmers 1-24 on Scene B and

faders 25-48 control dimmers 1-24 on Scene A.

If both Scenes are active, the fader at the higher level sets the output

level for the dimmer. This is called “Highest-Takes-Precedence” or HTP

operation. SmartFade determines which fader is at the highest level by

looking at the individual channel fader level, and the level of the

crossfader mastering that channel fader’s Scene. The channel fader at

the higher proportional level “wins” and generates the output for the

console.

Two Scene Operation:

1: Set channel levels on Scene A, faders 1-12 (or 1-24).

2: Lower both Crossfaders to the bottom of their travel to

fade up the levels in Scene A. Scene A is live, and Scene

B is safe.

3: Set channel levels for Scene B, faders 13-24 (or 25-48).

4: When it’s time to crossfade from Scene A to Scene B,

move both Crossfaders from the bottom of their travel to

the top of their travel. Scene B is now live, and Scene A

is safe.

5: Repeat steps 1-4 as needed to play back each look in

your show.

Power-up in Two Scene Mode:

The power button turns the unit on and off. It is also used to set the operating mode of the

SmartFade (see below).

• Press for less than 5 seconds to turn unit on.

• To shut down the SmartFade, press . The LCD displays a confirmation message. Press to

shut down, or [<] to cancel and resume normal operation.

Bump Buttons:

Bump button LEDs light to indicate when a fader is contributing to the live

output of the console. The LEDs fade up as the individual fader’s output

increases, and it fades down as the output decreases. As you crossfade

from Scene A to Scene B, the Scene with the lit bump buttons is the live

Scene, and the one with the dark bump buttons is the safe Scene.

When pressed, a bump button forces the output of that fader to the level

set at the BUMPS master fader.

• Bump buttons can operate in pile-on mode, where the level generated

by pressing the button adds into the live output.

• They can also operate in SOLO mode. Press [SOLO] to activate SOLO

mode. Pressing a bump button in SOLO mode overrides all console

output and instead outputs only the bumped channel(s).

Master Fader and BLACK OUT:

• The Master fader proportionally limits all

outputs (except for IND 1 and IND2). Keep

the Master fader at “10” to ensure full output

of the dimmers. When the Master fader is

below “10” the [BLACK OUT] button blinks.

• Press [BLACK OUT] to engage a dead black

out. The key lights bright blue when

activated. All outputs (except IND 1 and IND

2) are forced to zero when engaged and all

buttons except IND 1 and IND 2 go out.

• Press [BLACK OUT] again to disengage the

black out. All outputs are restored and the

[BLACK OUT] key goes dark.

IND 1 and IND 2:

Independent 1 and 2 provide two output channels that are

separate from the effect of all other controls. They are intended

to operate devices such as smoke machines, tab tracks, cue

lights, etc. IND 1 and 2 are always either full on or full off.

• If the console is patched 1-to-1, IND 1 toggles the state of

DMX 97 and IND 2 toggles the state of DMX 98.

• IND 1 and 2 (indicated as “i1” and “i2”) may be patched to

any DMX channels in the same way as other console

channels. Custom patching must be performed in Normal

mode. See the SmartFade User Manual for instructions.

• IND 1 and IND 2 may be affected by the most recent settings

made in Normal mode.

• You must set patch to “custom” in Normal Mode for IND1 and

IND2 to function in Two Scene Mode.

LCD Menu:

The LCD menu provides quick access to configuration settings.

• Press [] to enter the menu, to move to subsequent levels in the menu, and to accept setting

changes.

• Use the dial to scroll through menu items.

• Press [<] to return to previous menu levels without saving any pending change.

• Press [<<] to cancel out of the menu. Any recording or programming operation underway is

cancelled.

Note: SmartFade 1248 shown - SmartFade 1296 and 2496 also available.

Change into Two Scene mode:

• Console must be off, before changing modes.

• Press and hold [] for 5 seconds to enter the operating modes menu. Use the dial to step

through the available operating modes. When the desired mode is displayed, press the []

button. Available modes: Two Scene (described in this guide), Normal and DMX Backup

(described in the SmartFade User Manual).

SmartFade v2.0 Two Scene Quick Guide

7219M1300-2.0.0-EN



Rev A



Released 12/2008



Corporate Headquarters



3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin,

53562-0979 USA



Tel: +1 608 831 4116



800 688 4116



Fax: +1 608 836 1736



800 555 8912



Email: mail@etcconnect.com

London, UK



Unit 26-28, Victoria Industrial Estate, Victoria Road, London, W3 6UU, UK

Tel: +44 (0)20 8896 1000



Fax: +44 (0)20 8896 2000



Email:mail@etceurope.com

Rome, IT



Via Ennio Quirino Visconti, 11, 00193 Rome, Italy



Tel +39 (06) 32 111 683



Fax +44 (0) 20 8752 8486

Holzkirchen, DE



Ohmstrasse 3, 83607 Holzkirchen, Germany



Tel +49 (80 24) 47 00-0



Fax +49 (80 24) 47 00-3 00



Email:

[email protected]

Hong Kong



Rm 1801, 18/F, Tower I Phase 1 Enterprise Square,

9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong



Tel: +852 2799 1220



Fax: +852 2799 9325



Email:[email protected]om

Web:

www.etcconnect.com

Two Scene Menu

Settings

Patch

Diagnostics

Software Version

Use:> 1:1/Custom

Buttons

Display

Language

DMX In

Default time <adjust with dial>

Data Loss

Brightness

Contrast

Intensity: > %

[display version]

> %

Keep/Fade Out

English/Français/Deutsch/Español/Italiano

Shrnutí obsahu

Strany 1

Faders:Use the faders to set levels for individual control channels. If SmartFadeis set to use a 1=1 patch, fader 1 controls dimmer 1, fader 2 contro

Komentáře k této Příručce

Žádné komentáře

Etc SmartFade v2.0.0 Two Scene Quick Guide Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Kontrolní panel Etc SmartFade v2.0.0 Two Scene Quick Guide. ETC SmartFade v2.0.0 Two Scene Quick Guide User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Kontrolní panel Etc SmartFade v2.0.0 Two Scene Quick Guide