Etc SmartFade ML v3.0.1 Uživatelský manuál Strana 22
- Strana / 104
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
14 SmartFade ML v3.0.1 User Manual
LCD & Wheel Functions
The LCD menus provide quick access to functions. Parameters in the LCDs, page 45
Right LCD - Main menu
The right LCD, with one wheel, is the main menu for entering and exiting functions.
Left LCD - Sub menus
The left LCD provides control of functions in sub menus. Use the wheels to set values and
the SEL and MORE buttons to toggle choices.
LCD - Preview mode
In preview mode it’s possible to see programmed intensities for MEMS faders 1-24
Action Console Feedback
Activate menus
Scroll through choices Wheel (3) Choices are shown over the wheel. Use the
Menu button again to move to subsequent
levels, and to accept setting changes.
Previous choice Return to previous menu level.
Exit Cancels out of the menus.
Action Console Feedback
Activate preview mode Bumps 1-24 start blinking. Press again to
deactivate preview mode.
Select fader ... The selected Bump stops blinking. The LCD’s
will show intensities for the currently selected
fader mode A/B/D. “IFCB” indicates the type
of data recorded in the current memory.
<
<<
SEL
MORE
SMART
SOFT
1
24
- Control Console 1
- User Manual 1
- Table of Contents 3
- Chapter 3 4
- Chapter 4 5
- Chapter 5 5
- Appendix A 6
- Introduction 7
- Using this Manual 8
- Americas 9
- United Kingdom 9
- Unpack & Connect 10
- Power-up Procedure 10
- Shutdown Procedure 10
- Operating Modes 11
- Save Show to Card 12
- Quick Save Show to Card 12
- Load show from Card 13
- Load Patch from Card 14
- Load Personalities from Card 14
- Format SD Memory Card 15
- General Information 17
- Control Capacity 18
- Frontpanel Functionality 19
- Faders & Bump Buttons 20
- Independents 20
- 1 General Information 13 21
- Crossfader 21
- Record & Edit Functions 21
- The Select Section 21
- LCD & Wheel Functions 22
- Philosophy of the Console 23
- Data Structure & Timing 24
- Chapter 2 25
- DMX Output 26
- Clear/Set Patch 27
- Patch Dimmers (INT) 28
- 2 Setup 21 29
- Patch by Channel 29
- Patch Independents 30
- Patch Devices 31
- Device Commands 32
- View/Modify Device Patch 32
- 2 Setup 25 33
- Device Settings 33
- Console Setup 34
- Setup 27 35
- Software Version 36
- LED Calibration 36
- Save LED Calibration 36
- Load LED Calibration 36
- MIDI Setup 37
- Synchronising Two SmartFades 38
- Basic MIDI Implementation 38
- 2 Setup 31 39
- MIDI Channel 39
- Sending MIDI Controllers 39
- Open the Personality Editor 40
- 2 Setup 33 41
- Edit a Personality Live 41
- Edit a Personality Blind 42
- 2 Setup 35 43
- 2 Setup 37 45
- Special - Fade With Intensity 45
- Special - Invert Parameter 45
- Intensity Channels 48
- 3 Program 41 49
- Adjust Channel Range 49
- Set Channel Range 49
- 3 Program 43 51
- Select Devices 51
- Device Groups 52
- 3 Program 45 53
- Device Parameters 53
- Color Control 54
- 3 Program 47 55
- Device Palettes 55
- General Device Functions 56
- 3 Program 49 57
- Highlight Mode 58
- 3 Program 51 59
- Shape effects 59
- 3 Program 53 61
- Color Effects 61
- Linear Effects 62
- Memories 63
- Record Selected 64
- Snapshots 65
- Sequences 66
- 3 Program 59 67
- Record a Sequence 67
- 3 Program 61 69
- Record the Stack from Bumps 69
- Record a Stack State or “Cue” 70
- 3 Program 63 71
- Edit Memories 74
- 4 Edit 67 75
- Delete a Memory 75
- Delete Multiple Memories 75
- Copy a Memory 75
- Default Device Times 76
- Memory FCB Times 76
- Edit Sequences & Stack 77
- Delete a Step 78
- Insert a Step 78
- 4 Edit 71 79
- Insert a PointQ 79
- Change the Content of a Step 79
- Copy a Sequence 80
- 4 Edit 73 81
- Run Modes 81
- Sequence & Stack Times 82
- 4 Edit 75 83
- Global Time For All Steps 84
- Edit Effects 85
- Edit Linear Effects 86
- 4 Edit 79 87
- Edit Color Effects 87
- Edit Palettes 88
- Playback 89
- General Functions 90
- How Memory Faders Interact 92
- Memory Rubberband 92
- Rate & BPM for Sequences 94
- Stack & Crossfader 95
- Change Times For The Stack 96
- Rate for the Stack 96
- 5 Playback 89 97
- Single Scene Crossfading 97
- Software Update 98
- USB Update 99
Související produkty a manuály pro Kontrolní panel Etc SmartFade ML v3.0.1
Kontrolní panel Etc SmartFade ML v3.0 Uživatelský manuál
(104 stránky)
(104 stránky)
(92 stránky)
Kontrolní panel Etc SmartFade ML v3.0 Uživatelský manuál
(100 stránky)
(100 stránky)
Kontrolní panel Etc Congo Family v6.4 Uživatelský manuál
(102 stránky)
(102 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce