ETC Source Four LED Series Uživatelský manuál Strana 70
- Strana / 96
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
65 Source Four LED Profile v1.4.0 User Manual
Slave
Any fixture in the data chain that is being controlled by the master fixture. By default, all
fixtures are slaves, except the one that had its Preset or Sequence altered most recently.
A Slave fixture can only directly imitate the performance of the Master fixture.
When operating as a Slave fixture, the fixture displays Slave on its home screen.
Diagnostics
The Diagnostics menu provides access to detailed information about various aspects of the
fixture’s performance. Diagnostics also provides access to test functions and fixture
recalibration. Much of the Diagnostics menu is used by service technicians to troubleshoot
problems.
Step 1: From the home screen, press [Enter] to open the Main Menu.
Step 2: Scroll to Advanced Settings.
Step 3: Press [Enter].
Figure-3.30 Selecting Diagnostics on the Advanced Menu.
Current DMX In
The Current DMX In screen displays the values of the current DMX input by channels. The
values dynamically change as the DMX input changes. This screen is a read-only screen,
which displays the following.
• The Control Input setting.
• The DMX channel assignment, in order.
• The current DMX value (0-255) of each control channel in use by the fixture.
• The current brightness (0 to full or 00 to FL) of each series of LEDs in the fixture's LED
array.
Step 1: On the Diagnostics screen, scroll to Current DMX In.
Step 2: Press [Enter].
Figure-3.31 Current DMX In Screen with Dynamic Values.
Step 3: Press [Up] or [Down] to scroll through the channels. Arrows on the left indicate
that you can scroll up or down.
Step 4: Press [Back] to return to the Diagnostics screen.
Advanced Menu
DMX Settings
LED Settings
Presets and Sequences
Diagnostics
Local Settings
Copy All Settings
Diagnostics
Current DMX In
Network Statistics
Test
Recalibrate Fixture
About Fixture
Current DMX In
DMX Ch Level
2 107
3 14
4 82
5 0
G O R A O R I
11 02 00 10 00 00 01
DMX channel
DMX value
Brightness
LED series
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Související produkty a manuály pro Světlomety ETC Source Four LED Series
Světlomety ETC ION Uživatelský manuál
(12 stránky)
(12 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce